Ask three roof cleaners how they’d clean your roof and you might get three different answers. One will jet wash it. One will scrape it by hand. Another will spray it and walk away. The method matters, because it decides how the roof looks afterwards, how long it stays clean and whether any harm is done along the way.
This guide compares the four methods we use, sets out what each is good and bad at, and explains why most roofs get a combination rather than one method alone.
The four methods at a glance
| Method | What it is | Best for | Watch out for |
|---|---|---|---|
| Hand moss removal | Scraping and brushing by hand with scrapers and stiff brushes; moss bagged and taken away | Every roof type, including clay, slate and historic roofs | Slower; needs safe access and care not to lift tiles |
| Soft wash with biocide | A biocide applied at low pressure to kill remaining moss, algae and lichen spores | Algae, black streaks, lichen and slowing regrowth after a clean | Needs a dry spell; product must be authorised for the use; run-off control |
| Steam cleaning | Hot water and steam at low pressure | Lifting dirt and growth from robust and some older surfaces without force | Still needs judgement on fragile or loose tiles |
| Controlled pressure washing | Water at a controlled, low setting, worked from the ridge down | Only sound, robust tiles, typically modern concrete, after a check | Never on clay, slate, old or fragile tiles; can strip colour if misused |
Our methods page sets out how we choose between them on each roof.
Hand moss removal
This is the foundation of almost every roof clean. Moss is scraped out of the laps and off the tiles with scrapers and stiff brushes, working with the tiles rather than against them. The moss is bagged and taken away, and the gutters are cleared of what falls.
It’s the method Wienerberger points to in its guide to cleaning roof tiles: remove moss with a trowel or stiff brush, ideally on a dry day. It suits every roof type, including clay, slate and historic roofs. Its limits are speed and the need for safe access. It also leaves fine spores and staining behind, which is where the next methods come in. See roof moss removal.
Soft wash with biocide
A soft wash applies a biocide at low pressure. It kills the moss, algae and lichen spores that hand removal leaves behind and slows regrowth. It’s also the gentle way to deal with black streaks and lichen, which shouldn’t be scraped hard. Dead growth then weathers off over the following weeks and months.
Two things matter. The product must be approved or authorised for the use in Great Britain, as HSE explains, and used as the label says. And run-off must be controlled, because GOV.UK guidance says only clean water should go into surface water drains. A biocide typically keeps regrowth back for around one to a few years, depending on shade and aspect. See soft wash roof cleaning.
Steam cleaning
Steam cleaning uses hot water and steam at low pressure. The heat does work that would otherwise need force. It loosens dirt, algae and the remains of moss so they rinse away, without blasting the tile surface. That makes it useful on surfaces where high pressure would be wrong, and on stubborn staining after the moss is off.
It isn’t a licence to treat a fragile roof roughly. Loose, cracked or delaminating tiles still need care, and some roofs are better left to hand work and a soft wash alone. See roof steam cleaning, or our comparison of steam and soft washing.
Need it done? Superior Roof Cleaning cleans roofs and clears moss across London and the South East. Call 01342 344 936 or get a fixed quote.
Controlled pressure washing
This is the method most likely to cause damage, so it’s the one we use least. Wienerberger advises against high-pressure jet washers because they can damage tile finishes, strip colour from concrete tiles and force water into interlocks and headlaps. If a pressure washer is used, it says to set it low and work from the apex downwards.
Our rule follows that. We use controlled pressure only on robust tiles, typically modern concrete, and only after checking their condition. We never use it on clay, slate, old or fragile tiles. Read will pressure washing damage roof tiles?
Why most roofs get a combination
Each method does one part of the job well. A typical clean looks like this:
- Hand removal of the moss, bagged and taken away.
- Clearing the gutters of the moss removed.
- Steam or, on robust tiles only, controlled pressure where the surface needs it.
- A soft wash biocide, if agreed, to slow regrowth.
On a clay or slate roof, step three is often left out or kept to low-pressure steam. On a historic roof, it may be hand brushing and a biocide only. The aim is the gentlest method that works, not the fastest.
Matching the method to the roof
The tile decides a lot. Clay tiles are prone to delamination when damp, so hand methods and soft wash suit them. Slate is brittle and can be lifted by pressure. Older fibre cement slates may contain asbestos, so they need a careful, low-impact approach. Concrete tiles are the most robust, but can lose colour under high pressure. For listed and historic buildings, see historic and listed roofs. Our guide to each tile type goes further.
What no method can do
Be wary of any method sold as permanent. Moss returns in time on almost every roof, sooner on shaded slopes. Biocide slows that; it doesn’t stop it. No method repairs tiles that are already cracked or delaminating, and no method should be used as a reason to walk all over a roof. A coating is a separate decision, with its own pros and cons. Read roof coatings: when they’re worth it.
Questions to ask about method
- Which methods will you use on my roof, and why?
- Will you use pressure anywhere? On which tiles?
- Is a biocide included, and is it authorised for this use in Great Britain?
- How will you control run-off?
- Will anyone walk on the tiles?
We’re happy to explain our choices for your roof. Call for a fixed quote.
Quick answers
What is the best way to clean a roof?
Usually hand removal of the moss, then a soft wash biocide, with steam where it helps. Controlled pressure only on robust tiles after a check.
Is soft washing better than pressure washing?
For most roofs, yes. It’s gentler, treats spores and slows regrowth without blasting the tile surface.
Is steam cleaning safe for roof tiles?
It works at low pressure, so it’s gentler than jet washing, but loose or fragile tiles still need care.
Do you use one method on every roof?
No. The tile type and condition decide the mix, and we use the gentlest method that works.
Related services
More advice
- Will Pressure Washing Damage Roof Tiles?
- Steam Cleaning vs Soft Washing a Roof
- Clay, Concrete, Slate or Fibre Cement: Cleaning Each
- How Long Does a Roof Biocide Treatment Last?
- How Much Does Roof Cleaning Cost? What Affects It
- All advice
This guide is general information, not professional advice for your roof. Every roof is different, and we’ll confirm what suits yours when we see it.